46203 - GE Enbrighten Z-Wave Plus In-Wall Smart Dimmer (by Jasco Products)
Please Note: The Jasco 46203 in-wall smart dimmer has been discontinued without replacement.
GE Enbrighten 46203 Product Description:
The GE Enbrighten 46203 is a Z-Wave Plus in-wall smart dimmer manufactured by Jasco Products (with white/light almond paddles included). The 46203 smart dimmer allows the end user to Turn ON/OFF and control the brightness level of the connected lighting manually or via Z-Wave hub or controller.
Set the scene with the Enbrighten Z-Wave In-Wall Smart Dimmer with QuickFit™ and SimpleWire™. When paired with a compatible hub, the hardwired smart dimmer operates wall, ceiling and accent lighting through individual commands and programmed settings. Wirelessly control and schedule indoor or outdoor fixtures for effortless management of your home or business.
The GE Enbrighten 46203 has a QuickFit™ design that includes improved components which reduce the housing depth by up to 20 percent compared to previous Z-Wave models and eliminated the need for heat tabs. With SimpleWire™ auto line-load sensing terminals, the GE Enbrighten 46203 supports fast installation by detecting line and load wires and configuring the switch accordingly. Dual ground ports, which are offset to avoid switch box mounting screws, support daisy-chaining in multi-switch setups.
This Z-Wave device has advanced features that allow you to customize your experience. The 46203 smart dimmer utilizes a full range of dimmability allowing the end-user to adjust the brightness level from 0-100% in 1% increments. These features can only be adjusted by a Z-Wave enabled controller that supports the Z-Wave configuration command class.
Product Features:
- Turn ON/OFF and control the brightness level of the connected lighting manually or via Z-Wave hub or controller
- Remotely monitor with any mobile device
- Works with Google and Alexa (requires compatible hub*)
- May be used in single pole installation or with up to four GE model 12723 or 46199 Add-on switches in 3, 4, 5 or 6-way wiring configurations
- Works with most dimmable LED, CFL, halogen and all incandescent bulbs
- Blue LED indicates switch location in a dark room (with 4 adjustable settings)
- Can be Included in multiple Groups and Scenes
- Utilizes the Z-Wave Firmware Update Meta Data command class for standardized firmware updates Over the Air
- Supports Advanced Configuration; Dim rates, LED status, minimum and maximum dim levels, Alternate exclusion
- Full Range Dimmability; adjust brightness level from 0-100% in 1% increments
- Screw Terminal installation; requires wiring connections for Line (Hot), Load, Neutral, and Ground. Traveler wire required for multi pole installation
- Uses a standard decora wall plate (wall plate not included)
- Interchangeable Paddle switch: White & light almond paddle included in package
- LED status can be inverted manually changed to invert, always OFF and always ON
- Inline traveler circuit protection
- White/light almond paddles included
- Z-Wave Plus certified
- Compatible with Z-Wave enabled controller
GE Enbrighten 46203 Product Specifications:
- Power: 120VAC, 60Hz
- Maximum Load: 600W Incandescent, 300 Dimmable CFL/LED
- Signal Frequency: 908.4/916 MHz
- Z-Wave Range: Up to 150ft. line of sight between the wireless controller and the closest Z-Wave receiver module
- Operating Temperature: 32°F - 104°F (0°C - 40°C)
- Environment: Indoor Use
- Warranty: 2-year limited product warranty
Please Note: The GE Enbrighten 46201 smart switch requires a neutral wire.
GE Enbrighten 46203 Product Documents:
• Data Sheet - GE Enbrighten 46203 Z-Wave Plus In-Wall Smart Dimmer
• User/Installation Guide - GE Enbrighten 46203 Z-Wave Plus In-Wall Smart Dimmer
GE Enbrighten 46203 Product Configuration:
- Adding your device to a Z-Wave network - Once the hub is ready to add your smart dimmer, press and release the top or bottom button on the smart dimmer to add it in the network.
- To remove and reset the device - Once the controller is ready to remove your device, press and release the top button on the smart dimmer to remove it from the network.
- S2 + SmartStart install - The controller's app will indicate if it has discovered the device. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the side of the box, or the QR code label on the product. Enter the 5-digit code.
- To return to factory defaults - Quickly press the ON button 3 times, then press the OFF button 3 times. The LED will flash ON/OFF 5 times when completed successfully.
