Product Features:

• ETL certified for UL639 and ULC S306
• 35-foot detection range with a 90-degree horizontal FOV
• Remotely configurable PIR sensitivity (Pet immunity, etc.)
• Easy Installation; Simple panel enrollment, No broadband required (No router configuration), Tri-color LED
• Battery powered
• Tamper detection, walk test mode, supervision
• Color images
• Night vision; IR illumination, Black and white images
• Wireless image transmission to panel
• Wireless image transmission to Alarm.com via cellular networks

Physical Data

• Dimensions (L x W x H): 3.0", 1.8", 1.8"
• Enclosure Material: Fire resistant plastic (UL 94)
• Enclosure Color: White
• Weight: 3.1 oz (with batteries, w/o mounting accessories)
• Operating Temperature: Indoors (32-110°F for non pet applications; 60-110°F for pet applications)
• Humidity: UL certified in up to 85% relative humidity
• Static Immunity: Yes
• Sealed Optics: No
• RFI Immunity: Yes
• Tamper Detection: Yes (orientation based detection)

Motion Detection

• Technology: Dual element PIR
• Detection Range: 35' with a 90° horizontal FOV
• Lens Type: Fresnel lens
• PIR Sensitivity: Remotely configurable; 3 levels
• Pet Immunity: Yes with low sensitivity level only (up to 40 lbs.)
• PIR White Light Immunity: Yes
• Walk Test Mode: Yes
• Post Activation Idle Time: 3 minutes (default when disarmed)

Camera

• Camera Type: CMOS
• Focus: 1 ft. to infinity
• Night Vision and Capture: Yes- automatic infrared flash (invisible 240mW)
• Night Vision Range: Optimal within 20 feet
• Minimum Illumination w/o IR Flash: 3 lux
• Motion Triggered Images: Yes
• Images On-Demand: Yes
• Image Resolution: VGA (640x480 pixels)

Wireless

• Frequency: 900 MHz
• Protocol: 802.15.4
• Open Air Range: 400 feet
• Antenna: Helical chip antenna
• Wireless Supervision: Yes
• Encryption: Yes

Electrical Data

• Operating Voltage: 2.3-3.5v
• Current Consumption (typical) <1mA
• Power Requirements: 2-AA 1.5v Lithium batteries
• Recommended Battery: Energizer Ultimate Lithium (included)
• Battery Life (typical): Approximately 3 years

Regulatory Compliance

• FCC: FCC ID: YL6-143IS300
• IC: IC: 9111A-143IS300
• RoHS: Compliant
• ETL: Certified for UL 639 compliance

• Mounting Height: 6 ft to 8 ft
• Mounting Angle: 6°, 12°, or 18° down angle
• Mounting Options: Wall mounted w/ bracket (flat or corner mount)

• Images - Alarms: 50 motion-activated images per Alarm event, across all image-capturing devices, for up to 10 alarm events per month
• Images - Limited: 100 panel disarm and alarm image uploads per month over broadband only. This add-on is included by default in the Interactive, Interactive + Automation, and Commercial packages, and only applies to customers using a panel with a panel camera.
• Images - Plus: 400 uploads per month for motion-activated alarm uploads and non-alarm (e.g., disarm, Peek-Ins, etc.) events with the base package, with a maximum of 40 uploads per month over a cellular network connection (Up to 200 additional uploads per month can be added to the service package)
  Note: Alarm event uploads count towards the limit, but images are always taken in the event of an alarm regardless of if the upload limit was reached.
• Extra Image Events: 200 uploads per month, with a maximum of 20 uploads per month over a cellular network connection

2GIG EDGE

• Panel firmware version A3.1.0.011+
• The 2GIG XCVR3 Transceiver Adapter for the Image Sensor must be installed in the panel.
• Device limit 10 image sensors.

2GIG GC2e

• Panel firmware version 1.23+
• The 2GIG XCVR5e Transceiver adapter for the Image Sensor must be installed in the panel.
• Device limit 3 image sensors.

2GIG GC3

• Panel version 3.0.1+
• The 2GIG XCVR3 Transceiver Adapter for the Image Sensor must be installed in the panel.
• Device limit 10 image sensors.

2GIG GC3e

• All panel versions are compatible.
• The 2GIG XCVR3 Transceiver Adapter for the Image Sensor must be installed in the panel.
• Device limit 10 image sensors.

Interlogix Simon XT

• Panel version 1.3 & up
• Alarm.com modules between versions:
* 146 - 185 require an Image Sensor daughterboard is attached for compatibility.
* Zone 39 must be reserved for the Image Sensor daughterboard, which is hardwired to the panel.
* 187-191j is compatible and does not require an Image Sensor daughterboard to be attached.

• Device limit 3 image sensors.

Interlogix Simon XTi

• Panel version 1.0+
• Alarm.com modules between versions:
* 151 - 185 require an Image Sensor daughterboard is attached for compatibility.
* 187-191j is compatible and does not require an Image Sensor daughterboard to be attached.

• Device limit 3 image sensors.

Interlogix Simon XTi-5

• All panel versions are compatible.
• Alarm.com modules between versions:

* 177 -185 require an Image Sensor daughterboard is attached for compatibility.
* 187-191j is compatible and does not require an Image Sensor daughterboard to be attached.

• Device limit 3 image sensors.

Interlogix Concord

• Panel version 4.0+
• Alarm.com modules between versions:
* 177+ on CDMA or 173+ on HSPA with an Image Sensor daughterboard version 104.0+ attached to the module.
* 187f-189f on Dual-Path LTE. A daughterboard is not required for this module version.

• Device limit 3 image sensors.

DSC Impassa

• Panel version 1.3+
• Requires the Alarm.com module that come with the Image Sensor daughterboard attached. The SKU numbers for these Alarm.com modules are 3G8055(l) or CD8055(l).
• Device limit 3 image sensors.

DSC PowerSeries Neo

• Panel version 1.10+
• Alarm.com module versions:
* 185 and lower must be one of the modules that come with the Image Sensor daughterboard attached. The SKU numbers for these Alarm.com modules are 3G8080(l) or CD8080(l).
* 187+ is compatible and does not require an Image Sensor daughterboard to be attached.

• Device limit 3 image sensors.

DSC PowerSeries Pro

• Panel version 1.01+
• No additional daughterboard required since the communication hardware is built-in to the cellular module.
• Device limit 3 image sensors.

DSC Touch

• All firmware versions of the DSC Touch are compatible.
• No additional daughterboard required since the communication hardware is built-in to the panel.
• Device limit 5 image sensors.

Qolsys IQ Panel

• All firmware versions of the Qolsys IQ panel are compatible.
• No additional daughterboard required since the communication hardware is built-in to the panel.
• Device limit 5 image sensors.
• Note: Qolsys may refer to the Image Sensor version 1 and 2 as QZ8100 and the Image Sensor version 3 as QZ8103.

Qolsys IQ Panel 2

• All firmware versions of the Qolsys IQ Panel 2 are compatible.
• Requires the Qolsys Image Sensor daughterboard.
• The Qolsys IQ Panel 2 Plus is not compatible since it has a built-in PowerG daughtercard, which uses the same antenna as the Image Sensor daughtercard.
• Note: Qolsys may refer to the Image Sensor version 1 and 2 as QZ8100 and the Image Sensor version 3 as QZ8103.