PROSiXSMOKEV - Resideo Honeywell Home Wireless Smoke/Heat Detector (for ProSeries Control Panels)
ProSeries PROSiXSMOKEV Product Description:
The Resideo Honeywell Home PROSiXSMOKEV is a wireless combination heat/smoke detector that is intended for use with control panels that support PROSiX-Series devices. The PROSiXSMOKEV heat/smoke detector is compatible with the ProSeries PROA7, ProSeries PROA7C, ProSeries PROA7PLUS or ProSeries PROA7PLUSC all-in-one wireless touchscreen control panels. The PROSiXSMOKEV multi-criteria smoke detector employs advanced levels of detection and discrimination. It reduces common cooking nusiance alarms and allows faster detection to different types of fire conditions.
The PROSiXSMOKEV detector reports the following signals in addition to detecting smoke conditions. It detects for two specific heat conditions; fixed heat above 135° F and rate-of-rise detection for greater than 104° and 15°F temperature rise per minute. The detector alarms when 135° F; is exceeded and restores when it falls below 135° F. However, the thermistor is damaged at 195° F and the integrity of the detector itself is compromised and needs to be replaced if that occurs.
It also sends maintenance signals when the chamber is contaminated and requires cleaning. An end-of-life signal will be sent when the PROSiXSMOKEV device is no longer functional and needs to be replaced entirely. A base tamper signal will be sent to to the control panel when the smoke head is removed from the base. A supervision signal is sent to the panel every 200 seconds to check-in for system compatibility. Additionally, a signal and battery strength signal is also sent so you know when the sensor is out of range or the batteries are low and need replacement. If programmed into the control panel to operate in One-Go-All-Go mode, all smoke detectors programmed as One-Go-All-Go in the system will sound on alarm.
The PROSiXSMOKEV tamper will alert if the detector is removed from the base. It will send a tamper signal to the control panel. The tamper can be made tamper-proof to prevent unauthorized removal from the base. To do so, simply break off the small pillar on the base. This causes the detector to latch to the base. Form this point on, to remove the detector from its base, you must use a small screwdriver to release the catch and twist the the detector counter-clockwise. A screw can be added to prevent removal from the base.
To enroll and setup the device, you must enroll it in the control panel. When prompted, activate the PROSiXSMOKEV by pulling the battery tab or, if already powered, press the Test button to enroll. It enrolls into 2 zones: smoke detection into one zone and heat detection into a second zone. If the detector is not successfully enrolled during the enrollment period, the LED turns off and the device powers down. Activate the tamper or press the Test Button to restart the enrollment. The enrollment time varies depending on the signal strength between the device and the control panel. Once enrolled in a system, the detector cannot be used with another system until it is removed from the current one.
Before mounting the PROSiXSMOKEV detector permanently, conduct a Walk Test to verifiy adequate signal strength and adjust the device location and orientation as necessary. Refer to the Limitation of Fire alarm systems document for detailed information on detector spacing, placement zoning and special applications. The detector can be mounted on the ceiling or on the wall. Select a location and mount using the included mounting hardware.
The detector should be tested immediately after installation and at least once a year. Notify the central station that the smoke detector is undergoing tests, so we do not dispatch the authorities. You may choose to test the detector by; pressing the Test Button, smoke entry test (using canned smoke), direct heat test (by using a hair dryer spaced 12" or further away and blowing heat at the sensor). The PROSiXSMOKEV has one-green LED and a seperate bi-color (red and yellow) LED with an 85dB sounder. To clean the detector, carefully vacuum the side vents all the way around, then, wipe them with a clean damp cloth and dry thoroughly. Do NOT attempt to take the detector apart. This could result in damaging the unit.
Product Features:
- 128-bit AES Encryption (PROSiX-Series)
- Combination Smoke and Heat Detector
- Built-in 85dB Audible Siren
- Base Tamper
- LED indicators
- 360° Detection Pattern
- One-Go / All-Go Feature
ProSeries PROSiXSMOKEV Product Documents:
• ProSeries PROSiXSMOKEV Wireless Smoke/Heat Detector - Data Sheet
• ProSeries PROSiXSMOKEV Wireless Smoke/Heat Detector - Installation and Setup Guide
• ProSeries PROSiXSMOKEV Wireless Smoke/Heat Detector - Quick Installation Guide
• ProSeries PROSiXSMOKEV Wireless Smoke/Heat Detector - Applications Guide
• ProSeries PROSiXSMOKEV Wireless Smoke/Heat Detector - Limitations Guide
ProSeries PROSiXSMOKEV Product Specifications:
- Dimensions (Diameter x Depth): 5.3" x 1.6" (135mm x 42mm)
- Mounting Hardware: Included
- LED Indicators: Yes
- Tamper Protected: Yes (Base Tamper)
- Detection Pattern: 360 degrees
- Siren: Built-in 85dB sounder
- Maximum Spacing: 50ft x 50ft (refer to National Fire Alarm Code Standard NFPA 72)
- Transmission Range: 300 ft (92 meters)*
- Frequency: 2.4 GHz
- Power Requirements: 3V CR123 battery (Qty 2; Panasonic CR123A, Resideo 466)
- Encryption: 128-bit AES
- Operating Temperature: 32° to 95°F (0° to 35°C)
- Relative Humidity: 5-95%, non-condensing
- Agency Approvals: FCC/IC, ETL Listed to UL 268 and ULO 521, cETL Listed to ULC-S530 and ULC-S531
- Authorized Countries: US, Latin America
* Range can vary depending on building construction, wireless interference, and other factors.
Product Reviews
Trusted brand, July 11, 2022
Easy to install & pair, January 23, 2022
Posted By: kaiser
3 people found this review helpful
Highly recommend!! We replaced our hardwired smoke detectors with these wireless Smoke/Heat detectors. The box comes paired together. It was super easy to pair. We installed a total of 7 detectors in about 30 minutes.
3 people found this review helpful
Highly recommend!! We replaced our hardwired smoke detectors with these wireless Smoke/Heat detectors. The box comes paired together. It was super easy to pair. We installed a total of 7 detectors in about 30 minutes.
It?s affordable and does it?s job, January 19, 2022
Posted By: Reggie williams
1 people found this review helpful
This Smoke/Heat detector is excellent as far as general operation and installation. The directions were easy to follow and it only took me like minutes to test and install. The test runs through the smoke and heat alarms so that you have an introduction as to what to expect of the alarm does go off.
1 people found this review helpful
This Smoke/Heat detector is excellent as far as general operation and installation. The directions were easy to follow and it only took me like minutes to test and install. The test runs through the smoke and heat alarms so that you have an introduction as to what to expect of the alarm does go off.
Great Smoke Alarm, August 21, 2021
Posted By: Mark Braun
2 people found this review helpful
I liked that this was such an easy install. I just read the instructions and followed their simple steps and these units are easy to swap out with a preexisting detector, and we have peace of mind knowing we have both technologies.Really economical option for smoke/heat detectors.I am very pleased and feel safer with this product.
2 people found this review helpful
I liked that this was such an easy install. I just read the instructions and followed their simple steps and these units are easy to swap out with a preexisting detector, and we have peace of mind knowing we have both technologies.Really economical option for smoke/heat detectors.I am very pleased and feel safer with this product.
